FREE SHIPPING

                  On All Order Over 69.99 Lower 48 States ONLY

                 Does NOT Include Oversize, Truck Freight

                            Or Sale & Discounted items  

                            We ship International at EXACT shipping cost


 
 

Call us!

Monday - Friday

7:30am - 4:30pm PST

 206-381-3500.

Ask for Kaelee, Cari, Lynn, or Don.

Our Mailing address is:

Vic's 66

221 Woodworth Street.    

Sedro Woolley WA 98284                                                                                  

 

How to's & Step-By-Step Instructions

How to Apply Vinyl Decals 

Also Available in Printable PDF Format.

Once you have decided where you want to place the decal, Be sure to clean that surface thoroughly.

  1. Apply soapy water to the surface on which you will be placing the decal (We recommend using a spray bottle with lukewarm water & a couple of drops of liquid dishwashing soap).
  2. Remove the backing material from the decal to expose the adhesive surface.
  3. Note: Be sure to double check your measurements for center and levelness before proceeding.
  4. Apply the decal on top of the wet, soapy area positioning the decal in the desired location. 
  5. With a squeegee or soft sponge, push out the excess water, moving from the center of the decal outwards past the edges of the decal to form a "Perfect Bond".
  6. If using on an outdoor piece, allow 24 hrs to dry completely before exposing to the elements.

While your waiting for your new Decal to dry, please take a look at additional Decals that might interest you.

How to apply “Face-down” Water Transfer Decals

Also Available in Printable PDF Format.

  1. The surface upon which the decal is to be mounted must be clean and smooth. Surface imperfections remain visible beneath the decal. The temperature of the work surface is Important: DO NOT Apply to a COLD surface. If necessary warm the surface with a heat lamp or hair dryer.

  2. To remove the paper backing, soak in a shallow pan of warm water. DECAL SIDE OF PAPER FACE UP. The water should contain 1 or 2 drops of liquid dish washing detergent, this helps the decal “slide”. IMPORTANT: SOAK IN WATER FOR ONLY 10 SECONDS. DO NOT LET THE DECAL “CURL” WHILE SOAKING. After 10 Seconds of, pull the decal out of the water and lay it on a flat counter top or table for 3 to 5 minutes.

  3. The decal is ready for application when you can slide it sideways on it's paper backing. CAUTION: The decal can tear if pulled to hard.

  4. Wet the surface to which the decal will be applied using some of the warm soapy water.

  5. DO NOT TRY TO PICK THE DECAL OFF THE PAPER. Instead, carry the paper (with decal still attached) to the surface to which it will be applied. IMPORTANT: APPLY TO SURFACE WITH DECAL ISDE OF PAPER FACING DOWN SO THAT THE PAPER IS ON TOP OF THE DECAL AS YOU LAY IT ON THE SURFACE. Place the decal in the approximate position you want, pat down on the paper gently then carefully “slide” the paper off of the decal.

  6. Use a wetted pad of soft cloth on the surface of the decal to work trapped air and water from under the decal. Work from the center outward. The decal will remain moveable until all air and water are removed, the decal sticks. Check position of decal frequently as you work!!

  7. View decal across a low-angle light to check for any remaining air or water bubbles. A stubborn bubble that refuses to move outward can be deflated with a needle.

  8. We Strongly recommend clear-coating over these decals. Consult with your local supplier for application instructions, let them know that these are lacquer-based water-transfer decals.

How to Apply "Face-Up" Water Transfer Decals

Also Available in Printable PDF Format.

  1. The surface upon which the decal is to be mounted MUST be clean and smooth. Surface imperfections remain visible beneath the decal. The temperature of the work surface is important: DO NOT apply to a cold surface. If necessary warm the surface with a heat lamp or a hair dryer.
  2. To remove the decal from the paper backing, soak in a shallow pan of warm water. DECAL SIDE OF THE PAPER FACE UP. The water should contain 1 or 2 drops of dishwashing detergent; this helps the decal slide. IMPORTANT: SOAK IN WATER FOR ONLY 10 SECONDS. DO NOT LET THE DECAL CURL WHILE SOAKING.
  3.  The decal is ready for application when you can slide it sideways on its paper backing. CAUTION: The decal can tear if pulled to hard.
  4. Wet the surface to which the decal will be applied using some of the warm soapy water.
  5. DO NOT TRY TO PICK THE DECAL OFF THE PAPER. Instead, carry the paper ( with the decal still attached ) to the surface to which it will be applied. IMPORTANT: APPLY TO SURFACE WITH DECAL SIDE OF THE PAPER FACING UP SO THAT THE DECAL IS ON TOP OF THE PAPER AS YOU LAY IT ON THE SURFACE. Place the decal in the approximate position you want, and then carefully slide the DECAL off the PAPER and onto the surface where you want the decal applied. Pat down on the decal gently after it is on the surface.
  6. Use a wetted pad or soft cloth on the surface of the decal to work trapped air and water out from under the decal. Work from the center outward. The decal will remain moveable until air and water are removed, then the decal sticks. Check position of the decal frequently as you work!
  7. View decal across a low-angle light to check for any remaining air or water bubbles. A stubborn bubble that refuses to move outward can be deflated with a needle.
  8. We strongly recommend clear-coating over these decals. Consult with your local paint supplier for the directions; let him know that these are lacquer- based water-transfer decals. 

Bennett Models 900 & 1000 Window Replacement with RB-103 Locking Rubber Moulding

Download the printable PDF 's. Page 1 Page 2 Page 3 (these are large files so that they maintain their quality.)

Images are directly from the original Bennett Service Department Bulletin.

Tokheim Models 300 & 39 Short Door Window & Ad Glass Installation Using RB-102 Rubber. 

Download the printable PDF 's. Page 1 (these are large files so that they maintain their quality.)

Images are directly from the original Tokheim Service Department Bulletin.

Gilbarco series 900 Door Window & Ad Glass Installation Using RB-105 Rubber

  Rubber is installed on the back side of the door with curved groove attaching to the door and window or ad glass going into the square groove,  Also notice how the rubber is relief cut on the back side in the corners for the glass to protrude out of the rubber on the corners only.